honda305 Home honda305 Auctions honda305 Gallery honda305 Forum


honda305.com Forum

Login
□ Search
□ FAQ 
□ 
Vintage Honda Owners,
Restorers, Riders and
Admirers

Adjusting Valves

sibes67
honda305.com Member
Posts: 91
Joined: Wed Nov 16, 2011 8:03 pm
Location: Fremont, Wisconsin

Adjusting Valves

Post by sibes67 » Thu Dec 27, 2012 10:26 pm

Been trying, in vain, to find some type of tutorial for valve clearance adjustment. Where to look for this? Thanks,
Ron

LOUD MOUSE
honda305.com Member
Posts: 7817
Joined: Mon Aug 15, 2005 8:23 am
Location: KERRVILLE, TEXAS

Re: Adjusting Valves

Post by LOUD MOUSE » Fri Dec 28, 2012 8:36 am

Set rotor to "T" and adjust both right side valves to .004.
Set to "LT" and adjust left side.
You will need to lock down the rotor to do this. ...........lm

sibes67 wrote:Been trying, in vain, to find some type of tutorial for valve clearance adjustment. Where to look for this? Thanks,
Ron

sibes67
honda305.com Member
Posts: 91
Joined: Wed Nov 16, 2011 8:03 pm
Location: Fremont, Wisconsin

Re: Adjusting Valves

Post by sibes67 » Fri Dec 28, 2012 4:32 pm

LOUD MOUSE wrote:Set rotor to "T" and adjust both right side valves to .004.
Set to "LT" and adjust left side.
You will need to lock down the rotor to do this. ...........lm

sibes67 wrote:Been trying, in vain, to find some type of tutorial for valve clearance adjustment. Where to look for this? Thanks,
Ron
OK sounds good, but to be sure and since I have never done this before, here is a picture of where I think I approach this procedure...does the feeler gage insert under the adjusting screw and on top of the valve stem? The gauge hardly goes in very far right now, and I do have rotor lockied at T for this right side shot (shows intake, but the exhaust was really tight too). Thanks for the direction.

Image
Tappet Adjustment by sibes67, on Flickr

Ford Guy
honda305.com Member
Posts: 98
Joined: Mon Nov 26, 2007 5:59 pm
Location: New Berlin Wisconsin

Post by Ford Guy » Fri Dec 28, 2012 7:51 pm

It may be a little difficult with that feeler gauge. The one that came in the original tool kit is much narrower. The wider gauge will hang up on the valve cap making it harder to feel the clearance. What I did was cut my gauge down with a very sharp scissors and made sure there was not a burr on the sides. Other than that you are on the right track

sibes67
honda305.com Member
Posts: 91
Joined: Wed Nov 16, 2011 8:03 pm
Location: Fremont, Wisconsin

Post by sibes67 » Sat Dec 29, 2012 3:46 pm

My feeler gauge is 1/2 inch wide, most likely a automotive type gauge and not made for these bikes, and it did not come in the tool kit. My tool kit did not have a gauge in it; I will search for a different one that is easier to use. Thanks.

CliffC
honda305.com Member
Posts: 256
Joined: Sat Jan 13, 2007 3:52 pm
Location: Roseburg, Oregon

Post by CliffC » Sat Dec 29, 2012 7:12 pm

Narrower is what you need and if it has a bend in it, that's even better. I have a set that has about a 65 degree bend about an inch from the end, had them for years but don't remember where I got them. Cliff

User avatar
brewsky
honda305.com Member
Posts: 1816
Joined: Wed Jul 23, 2008 5:21 am
Location: Princeton, WV

Post by brewsky » Sat Dec 29, 2012 7:48 pm

Make sure the 'T' and 'LT' are when the piston is on compression stroke.
66 dream, 78 cb750k, 02fz1, 09 wing

Post Reply




 

CB-77 | CYP-77 | Road Test | Riding Log | Literature | Zen | Marketplace | VJ Survey | Links | Home