honda305 Home honda305 Auctions honda305 Gallery honda305 Forum


honda305.com Forum

Login
□ Search
□ FAQ 
□ 
Vintage Honda Owners,
Restorers, Riders and
Admirers

The Neverending Tale of a '65 Superhawk Restoration

Want to keep a Restoration Log? Post it here! You can include photos. Suggested format: One Restoration per Thread; then keep adding your updates to the same thread...
User avatar
cfloren
honda305.com Member
Posts: 52
Joined: Fri Jan 05, 2007 2:21 am
Location: Torrance, CA

Post by cfloren » Thu Oct 29, 2009 10:17 pm

Now it's wheel time. My old wheels were mismatched, bent, rusty and ugly. The front was an aluminum shouldered rim, of unknown brand. It was the bent rim that caused my front tire blowout, mentioned at the beginning of my restoration thread. The rear was one of the original chromed steel rims. The hubs showed the usual oxidation and staining. I found a few bent spokes but mostly they were just rusty.


As removed from the bike:

Image


Front aluminum rim:

Image


Front hub:

Image


Rear hub:

Image


I cut the old spokes out but saved an inner and outer from each wheel for reference. I cleaned the hubs thoroughly, then had a go at polishing them myself. The thing was, my cheap Harbor Fright (sic) buffing wheel leaves a lot to be desired in the power department. I couldn't apply enough pressure for long enough to get a good shine. Knowing that polishing labor is cheap, I decided to leave this job to the pros and dropped them off at a local shop, along with the brake backing plates.

The spokes went out to Buchanan's Spoke & Rim as examples for new stainless steel parts. I ordered my rims through them too. I settled on the Excel shouldered aluminum, WM2 (1.85) x 18" for the front and WM3 (2.15) x 18" for the rear. Originally I was going to lace them up and call the wheels done, but then something possessed me to have the rims polished and anodized black. I really dig the results.


Spokes identified and ready to go meet the spoke meisters:

Image

Image


New stainless spokes laced to new Excel rims, hubs are shown after my mediocre polishing attempt:

Image

Image

Image

Image

Image


And finally, polished hubs + stainless spokes + stainless nipples + polished & black anodized rims =

Image

Image

Image

Image


Lacing was not so bad. It was tricky to get all the spokes in without scratching the rims, but I'm sure I didn't use the easiest method. I just looked at my photos of the old wheels and duplicated the pattern.

I recently trued them up myself, down to under 0.010" of runout both axially and radially.
And last night I finished mounting the tires.

More photos to come.
Last edited by cfloren on Mon Nov 26, 2018 4:51 pm, edited 1 time in total.

block
honda305.com Member
Posts: 6
Joined: Wed Sep 23, 2009 1:19 am

Post by block » Fri Oct 30, 2009 1:14 am

Those wheels are beautiful! Good show sir.

User avatar
davomoto
honda305.com Member
Posts: 2508
Joined: Sat Nov 18, 2006 7:36 pm
Location: Marin County CA

Post by davomoto » Fri Oct 30, 2009 2:53 pm

Those wheel are sick! Nicely done. I built the exact same set-up for deez cafe bike, without the anodizing. Can't wait to see them on the bike!

davomoto

User avatar
cfloren
honda305.com Member
Posts: 52
Joined: Fri Jan 05, 2007 2:21 am
Location: Torrance, CA

Post by cfloren » Fri Oct 30, 2009 3:37 pm

Thanks for the compliments. Wheels are a huge part of a bike's visual impact so I wanted to make them look as good as possible. And as you can see, although this bike is getting a full rebuild and restoration, it won't be 100% showroom stock.

I may even get the "Takasago EXCEL Rim" stickers in yellow text for the rims, to give them a finishing touch. The anodizing is really beautiful and easy to clean, but the downside is that it's easy to scratch through to bare aluminum underneath with a steel spoke wrench or tire iron (don't ask how I know).

User avatar
davomoto
honda305.com Member
Posts: 2508
Joined: Sat Nov 18, 2006 7:36 pm
Location: Marin County CA

Post by davomoto » Fri Oct 30, 2009 5:14 pm

I've done several sets of anodized black supermoto wheels, and it's stressful making sure not to scratch someones new jewelry! I tape the crap out of the spoke wrench, and flat out refuse to mount the tires. Some shrinK wrap melted on tire irons is a good simple protection.

davomoto

Mike Mullins
honda305.com Member
Posts: 247
Joined: Thu Aug 02, 2007 9:24 pm
Location: Demotte IN

re:

Post by Mike Mullins » Fri Oct 30, 2009 5:31 pm

Chris: you are giving me ideas for Bob the Bobber that my wife will tell me I cant afford. VERY NICE !
Mike
"a free motorcycle is a bottomless hole intended solely for money"
66 CB 77
76 BMW R75/6
99 GL 1500 trike
75 & 79 XS 650's

Superchicken
honda305.com Member
Posts: 213
Joined: Sun Sep 16, 2007 10:10 am
Location: Turlock, Ca.

Post by Superchicken » Fri Oct 30, 2009 6:10 pm

this guy, pulls the beads together tight, then slips, tire, on. No tool
Image

Post Reply




 

CB-77 | CYP-77 | Road Test | Riding Log | Literature | Zen | Marketplace | VJ Survey | Links | Home