honda305 Home honda305 Auctions honda305 Gallery honda305 Forum


honda305.com Forum

Login
□ Search
□ FAQ 
□ 
Vintage Honda Owners,
Restorers, Riders and
Admirers

Search found 27 matches

by johnnyroastbeef
Thu Oct 06, 2011 11:33 am
Forum: Transmission
Topic: loud clanking noise in 1st gear, is my trans broken?
Replies: 11
Views: 5052

Does it change gears? It's hard to tell from your description of problem whether it's a power issue, or a trans issue. Davo I can't really tell if the gear lever changes the gears sicne I can't get the bike moving on it's own power without clanking and stalling in first gear. the gear selector peda...
by johnnyroastbeef
Thu Oct 06, 2011 10:51 am
Forum: Transmission
Topic: loud clanking noise in 1st gear, is my trans broken?
Replies: 11
Views: 5052

It could be stuck between gears, or in a higher gear. It may be coincidental with the engine cleaning. Try rocking the bike forward and backward while shifting, and see if it is shifting up and down. How many miles did you ride it before this problem began? Davo The gear shift lever moves up and do...
by johnnyroastbeef
Thu Oct 06, 2011 10:05 am
Forum: Transmission
Topic: loud clanking noise in 1st gear, is my trans broken?
Replies: 11
Views: 5052

Sounds like you got some water in the points or other electrical, and it's only running on one cylinder. Make be other issues as well. The arm that goes on the splines for the shift shaft should ne at 11:00 or shifting will be affected. Davo Points are clean and dry. Ran some 1500 grit sandpaper th...
by johnnyroastbeef
Thu Aug 25, 2011 6:59 am
Forum: Ignition - Mechanical | Electronic
Topic: Bike wants to stall when clutch is fully engaged...timing?
Replies: 10
Views: 6437

Just out of idle curiosity, how is the bike when you push it around, and if you put it into first gear pull in the clutch and push it, how is it? The motor has compression and seems to sound function normally when it's not running but in gear. no clanking or sounds or anything. The clutch works fin...
by johnnyroastbeef
Wed Aug 24, 2011 1:15 pm
Forum: Ignition - Mechanical | Electronic
Topic: Bike wants to stall when clutch is fully engaged...timing?
Replies: 10
Views: 6437

The points which ark are dirty. Plane and simple. If ya can spray with a contact cleaner than while closed Pull a Business Card through them. This will clean that one and while ya at it ya should do both. ........................lm here's a link to youtube.com where i took some video of teh timing ...
by johnnyroastbeef
Tue Aug 23, 2011 7:20 am
Forum: Ignition - Mechanical | Electronic
Topic: Dropping a cylinder? Coil?
Replies: 5
Views: 4049

Re: Reply

johnny, the bike would start ok then under a load it would lose power. It wouldn't rev up but would stall if I opened the throttle any more. i could easily hear the tone change when this was happening and it would suddenly cut back in on both cylinders. I thought the old molded plastic coil may be ...
by johnnyroastbeef
Mon Aug 22, 2011 2:19 pm
Forum: Ignition - Mechanical | Electronic
Topic: Dropping a cylinder? Coil?
Replies: 5
Views: 4049

Re: Fixed

Hi all, replaced both spark plug caps with new ones and I got to looking at the ground wire today and it was corroded at the frame connection so I replaced the wire and both connectors as well. Bike started fine without the missing that had been present before. It ran without any missing or popping...




 

CB-77 | CYP-77 | Road Test | Riding Log | Literature | Zen | Marketplace | VJ Survey | Links | Home